The gate is a headstock ram, and motion direction of valve disc is perpendicular to the direction of the fluid, and valve can only be fully open and fully closed, can not be adjusted and the throttle. The gate valve is sealed through the valve seat and the valve disc, usually the sealing surface will surmount the metal material to increase the wear resistance, such as surfacing 1Cr13, STL6, stainl...

Electric actuator is combination of the actuator and control valve in the automatic control system. Its role in the automatic control system is to accept the signal from the regulator, and by its position and characteristics in the process piping, to regulate the flow of process media to control the production process within the required range.

In order for the long-term continuous normal operation, it is necessary to have regular maintenance and strict management for all equipment and equipment. Jinbin valves are connected with these devices and devicesTo play its control performance of the indispensable parts, therefore, Jinbin valves should be considered comprehensive maintenance and management problem.Jinbin valve MaintenanceJinbin V...

Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they cost less than other valve design, and are lighter weight so they need less support. The disc is positioned in the center of the pipe. A rod passes through the disc to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perp...

Valves can leak for a variety of reasons, including:The valve is not fully closed (e.g., due to dirt, debris, or some other obstruction).The valve is damaged. Damage to either the seat or the seal can cause leakage.The valve is not designed to close 100%. Valves that are designed for precise control during throttling may not have excellent on/off capabilities.The valve is the wrong size for the pr...

Six basic pieces of information are required to size and select a safety or pressure relief valve:Connection size and typeSet pressure (psig)TemperatureBack pressureServiceRequired capacity

(A) direction and position Many valves have directional, such as cut-off valves, throttle valves, pressure relief valves, check valves, etc., if installed reverse, it will affect the use of life and efficiency (such as throttle), or simply does not work (such as Pressure relief valve), and even cause danger (such as check valve). General valve, the direction of the valve body signs; if not, should...

(1) appear on the sealing surface of dirt and debris, etc., and the original seal of the plane blocked, so that between the valve core and the valve seat gap, leading to leakage of the valve. To solve this kind of problem, it is usually the dirt on the seal. And temporarily suspended in the preparation of the maintenance of the boiler, the first safety door to run the mound test, once the leakage ...

Water harvesting in commercial projects involves collecting rooftop rainwater, stormwater runoff, condensate from air handlers and greywater from showers, baths and lavatory sinks. This water is reused for non-potable applications such as toilet flushing, irrigation and cooling towers.Because it offsets the use of drinking-quality water, this reuse has the potential to save millions of gallons per...

Gate valve is basically used in fluid pipelines for controlling the flow of fluid. There will be one gate or wedge in gate valve and it will control the fluid flow. Shape of gate or wedge of gate valve will be a type of flat circular plate or rectangular plate. Sometimes, gate or wedge is also termed as disc of gate valve.valve which is used to open and close the gate valve. When handle wheel will...

Operation of gate valve, check valve etc.

The mechanism to control flow can vary based on the application of the valve. In general, there are two means of controlling flow through a valve.Linear motion valves use a closure member that moves in a straight line to allow, stop or throttle the flow. The closure device could be a disc, slat or flexible material, like a diaphragm. The closure device can be used to:Move a disc or plug into or ag...

Jinbin air release valve working process.

The double offset butterfly valve is a valve that has 2 counterbalance contrasts and the concentric butterfly valve. The principal balance is the pole that is spotted not in the middle of the plate yet found on somewhat behind the circle. This balance will make the valve has a nonstop fixing surface on the circle. The second balance is the pole that placed not in the funnel fixates line yet found ...

Teflon coated ball valves: Teflon has properties like non-adherence, resistance to extremely high temperature, resistance to atmosphere and artificial responses making it most suitable for Industrial coatings. Because of its properties, Teflon paint is unreasonable constraining the client to augment the paint use rather than Teflon. This is utilized both for positive and negative charging Teflon P...

Ball valve made of solid elements offers high durability, and have the ability to function perfectly even after long idle time. It has a sphere made of brass, stainless steel, or chrome plated brass, embedded inside the conduit. On the top of the sphere is a lever attached which can move in a quarter turn only. When the level lies parallel to the pipe, the sphere allows water to flow. When the lev...

Teflon coated ball valves: Teflon has properties like non-adherence, resistance to extremely high temperature, resistance to atmosphere and artificial responses making it most suitable for Industrial coatings. Because of its properties, Teflon paint is unreasonable constraining the client to augment the paint use rather than Teflon. This is utilized both for positive and negative charging Teflon P...

THT provide different kinds of gate valve you require.These are some essential parts you should consider while choosing gate valve

LUG BUTTERFLY VALVEThe lug version of the butterfly valve's design is similar to a 3-piece ball valve in that one end of the line can be taken off without having an effect on the opposing side. This can be executed by using threaded inserts, flanges, along with two sets of lugs (bolts) that don't utilize nuts since each flange features its own bolts. It's also important to note that you don't need...

The biggest difference between knife gate valves and gate values is that gate valves are manufactured to ANSI standards while knife gate valves comply with TAPPI standards. The gate valve is also flanged, wider dimensionally, ANSI pressure rated and its API leak tightness standards need to be met. Gate values are bi-directional, and widely used in fluid applications and they only come with metal s...

Check valves are self-activating safety valves that permit gases and liquids to flow in only one direction. The purpose of a check valve is to prevent process flow from reversing in the system which could damage equipment or upset the process. They are classified as one-way directional valves. Check valves are commonly found protecting pumps in liquid applications or compressors in gas systems whe...

Gate valves are used in many industrial applications including the oil and gas industry, pharmaceuticals, manufacturing, automotive, and marine. Non-rising stem gate valves are very popular on ships, in underground applications, or where vertical space is limited because they don't take up extra space. Gate valves can be used in demanding environments such as high temperature and high pressure env...

The media would get stuck between the wedge and the seat of a normal gate valve and prevent flow shut-off. Knife gate valves were specially designed with a sharp edge to cut through the pulp and seal.

A Butterfly valve is a quarter-turn rotational motion valve, that is used to stop, regulate, and start flow.Butterfly valves are easy and fast to open. A 90° rotation of the handle provides a complete closure or opening of the valve. Large Butterfly valves are usually equipped with a so-called gearbox, where the handwheel by gears is connected to the stem. This simplifies the operation of the valv...

You should perform inspection, testing, and maintenance on a regular basis. The precise length of time depends on the service conditions, valve condition, and level of performance desired.We recommend an initial inspection interval of no longer than 12 months.For valves equipped with a lift lever, we recommend a monthly “try lever test” to ensure the disc is free. The valve should be subjected to ...

First understand how to deal with the valve leakage, first of all to understand why there will be leaking, leakage, is the so-called know the reason and know why. The valve must be airtight and must have a good seal. If there is a problem with the seal, there will be a leak phenomenon.Valve as a control unit in the fluid delivery system, with cut-off, regulation, diversion, to prevent the flow, re...

Daily valve maintenance of the most basic knowledge :1The valve should be dry and ventilated indoor, both ends of the road to be blocked.2.Long-term storage of the valve should be regularly checked, remove dirt, and in the processing surface coated with anti-rust oil.3.After installation, should be regularly checked, the main inspection items:(1) Sealing surface wear. (2) stem and stem nut trapezo...

The capacity reach 10,000 tons in 2014.

1. First, we do the material test.2. The QC check the dimensions of the machining.3. We have hydraulic test bench, we will test each pcs of valve before ex-workshop.4. QC check the appearance of the valves and other sides.5. Package and delivery.

Control valves regulate the flow of fluids as the position of the valve plug or disk changes with the force from the actuator. For this the valve has to achieve different things:The fluid should be contained without external leakageThe capacity for intended service should be adequateThere should be proper end connections to combine with adjacent pipelines and actuator attachment means to permit tr...

Our brand is Jinbin valve, and our tradmark is THT.

Gate valves are designed for fully open or fully closed service. They are installed in pipelines as isolating valves, and should not be used as control or regulating valves. Operation of a gate valve is performed doing an either clockwise to close (CTC) or clockwise to open (CTO) rotating motion of the stem. When operating the valve stem, the gate moves up- or downwards on the threaded part of the...

We can supply many kinds of valves.The size is depend on the type of the valve.Butterfly valve: from DN40 to DN3000,Gate valve: from DN15 to DN1200,Ball valve: from DN15 to DN1200,Check valve: from DN15 to DN2000 (within different type)Globe valve: from DN15 to DN300Valves for steel plant: from DN15 to DN4000Goggle valve: from DN100 to DN3000.Sluice gate: from 100*100 to 3000*3000 and unstandard ...

Regarding the min. order quanlity, it is not limited, but large quantities will be offered more discount.

We can supply : 1. Manual Valves2. Electric valves3.Pneumatic valves4. Hydraulic valves5. Automatic valve

Our company usually delivery from Tianjin port, it is nearly from our company, it's around 17km from us.

Most of the times we don't think about the installation position of gate valves to install them in horizontal line with upward stem or horizontal stem or to install them in vertical line with horizontal stem. This may be surprising for you if somebody tells you that valve manufacturers only prefer to install larger size valves in horizontal lines with vertical stem and some of them cannot guarante...

Jinbin valve main products like "large-diameter flange butterfly valve, butterfly valve, gate valve, check valve, goggle valve, gas relief valve, vent ash ball valve, sluice gate, Hydraulic control valve, Strainers,bellows and others ", widely used for water, sewage, electricity, metallurgy, heating, construction, petrochemical and other industries.

The company has a large marketing team and sales network covering 30 regions and exported to Russia, India, Belgium, Brazil, Dubai, Korea, Singapore, Saudi Arabia, Philippines, Malaysia, Laos, Jordan, UAE, Polish, UK and Russia ,Taiwan and other countries and regions.

Products produced according to international standards also can according to API, ANSI, BS, DIN, NF, EN,KS and other foreign standards.